Magellan MG5000 Manuel d'installation Page 35
- Page / 56
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MG5000 31
Part 8: Alarm Options
8.1 Bell Cut-Off Timer
Section [747] = Partition 1, [748] = Partition 2
000 = Disabled, 001 to 255 minutes, Default = 4 minutes, 5 minutes minimum for ULC installations
After an audible alarm, the bell or siren will stop upon disarming of the partition or when the Bell Cut-Off Timer has elapsed,
whichever comes first.
8.2 Recycle Alarm
After the Bell Cut-Off Timer and the Recycle Delay have elapsed, the control panel will re-verify the zone status. If there are any
open zones, the control panel will generate another alarm. In one armed period, the control panel will repeat this sequence the
number of times defined by the Recycle Counter.
8.2.1 Recycle Alarm Delay
Section [714]
000 = disabled, 001 to 255 minutes, Default = Disabled
The Recycle Delay determines the amount of time after Bell Cut-Off that the control panel will wait before re-verifying
zone status.
8.2.2 Recycle Alarm Counter
Section [715]
000 = disabled, 001 to 255, Default = Disabled
The Recycle Counter determines the number of times the control panel will re-verify the zone status after Bell Cut-Off
in one armed period.
8.3 Tamper Recognition
8.3.1 Zones/RF Module and Keypad/Bus Module Tamper Recognition
Section [705]: Tamper Recognition Options
If a device has been tampered with (i.e. the anti-tamper switch has been set off), the Magellan MG5000 can generate
a trouble, an alarm, and/or transmit a report code to the monitoring station. The system will react to an RF zone and a
keypad/bus module differently.
8.4 RF and Keypad/Bus Module Supervision
Section [705]: Supervision Options
The Magellan MG5000 waits for each of its assigned wireless transmitters to send a status signal within a specified time period to
confirm their presence and functionality. If a device has not sent a signal within that time period, the Magellan MG5000 can
generate a trouble, an alarm, and/or transmit a report code to the monitoring station. The system will react to an RF zone and a
keypad/bus module differently.
[3] [4] Zones/RF Module Tamper Recognition Options Keypad / Bus Module Tamper Recognition Options*
OFF OFF Disabled
TROUBLE ONLY
OFF ON TROUBLE ONLY TROUBLE ONLY
ON OFF When disarmed: TROUBLE ONLY
When armed: Follow zone’s alarm type
TROUBLE ONLY
ON ON When disarmed: AUDIBLE ALARM
When armed: Follow zone’s alarm type
AUDIBLE ALARM
* Tamper recognition of keypad/bus module only if section [700] option [7] is enabled.
[6] [7] RF Supervision Options Keypad / Bus Module Supervision Options
OFF OFF Disabled Disabled
OFF ON
TROUBLE ONLY TROUBLE ONLY
ON OFF When disarmed: TROUBLE ONLY
When armed: Follow zone’s alarm type
TROUBLE ONLY
ON ON When disarmed: AUDIBLE ALARM
When armed: Follow zone’s alarm type
AUDIBLE ALARM
- MG5000 V1.4 1
- Table of Contents 3
- Part 1: Introduction 5
- Part 2: Installation 6
- MG5000 3 7
- MG5000 5 9
- 2.5 Auxiliary Power Terminals 9
- 2.6 Telephone Line Connection 9
- 2.7 Bell Output Connection 9
- 2.9 Single Zone Inputs 10
- MG5000 7 11
- 2.11 Fire Circuits 12
- Part 3: Programming Methods 13
- 3.2.3 Data Display Mode 14
- Part 4: Access Codes 15
- 4.5 User Code Options 16
- 4.6 Lock Master Code 17
- MG5000 13 17
- Part 5: Zone Programming 18
- MG5000 15 19
- MG5000 17 21
- 5.2 Zone Definition Status 21
- 5.3 Zone Partition Assignment 22
- 5.4 Zone Options 22
- MG5000 19 23
- 5.5 EOL Zones 23
- 5.6 ATZ Zone Doubling 23
- 5.7 ATZ Wiring Options 23
- Part 6: Wireless Features 24
- MG5000 21 25
- 6.3 Supervision Options 25
- 6.4 RF Jamming Supervision 25
- MG5000 23 27
- 6.9 Wireless Keypad Options 27
- MG5000 25 29
- 7.9 Timed Auto-Arming 32
- 7.10 No Movement Auto-Arming 32
- 7.14.1 Beep On Exit Delay 33
- 7.19 Exit Delay Termination 34
- 7.20 Fast Exit 34
- Part 8: Alarm Options 35
- MG5000 35 39
- 9.10 Personal Dialing Numbers 39
- 9.11 Reporting Formats 39
- 9.12 Dialing Method 40
- 9.25.1 TLM Fail Timer 42
- MG5000 39 43
- Part 10: Programmable Outputs 44
- MG5000 41 45
- 10.5 PGM Programming 45
- Part 11: System Settings 46
- 12.1.2 Number of Rings 48
- MG5000 45 49
- 12.6 Answer WinLoad Software 49
- 12.8 Call Back WinLoad 49
- Part 13: User Operation 50
- Magellan Series 47 51
- Magellan Series 49 53
- MG5000 51 55
- MG5000-EI03 56
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Magellan MG5000
(2 pages)
(68 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.845 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels