Magellan MG5000 Manuel d'installation télécharger pdf (Page 25)

MG5000 21

6.3 Supervision Options

The Supervision Options cannot be used with any remote controls assigned to the control panel.

6.3.1 Supervision Bypass Options

Section [705]: Arming/Disarming Options

Option [8] ON = Generate Supervision Loss if detected on a Bypassed Wireless Transmitter Zone

(default)

Option [8] OFF = No Supervision Loss if detected on a Bypassed Wireless Transmitter Zone

When this feature is disabled, the Wireless Transmitter Supervision Options will follow the zone’s bypass definition.

This means the control panel will not perform any action if a Supervision Loss occurs on a bypassed zone. When this

feature is enabled, the Wireless Transmitter Options will ignore the bypass definition. This means the control panel will

generate an incident as per Wireless Transmitter Supervision Options if a supervision loss occurs on a bypassed zone.

6.3.2 RF Supervision Timer Settings

Section [706]: Supervision Options

Option [1] OFF = Check-in supervision interval is every 24 hours (default)

Option [1] ON = Check-in supervision interval is every 80 minutes

Option [1] defines the time period that the control panel will expect a check-in status signal from its assigned wireless

transmitters. For example, if the timer is set to 80 minutes (option [1] = ON), the control panel will expect a check-in

status signal to be sent from its assigned wireless transmitters within 80 minutes. If the Magellan MG5000 does not

receive a signal from one of its wireless transmitters within the period of time defined here, it can then generate a

trouble, an alarm, and/or can transmit a report code to the monitoring station (see Supervision Options on page 21).

6.4 RF Jamming Supervision

Section [700]: Zone Options

Option [5] OFF = RF Jamming Supervision Disabled

Option [5] ON = RF Jamming Supervision Enabled (default)

With option [5] ON, a trouble will be generated when the panel’s RF signal is jammed or encounters interference for a minimum of

10 seconds.

6.5 Wireless Serial Number Display

Section [960]: Find Wireless Serial Number Display

To see the wireless serial number display, enter section [960]. Press the anti-tamper switch of the desired module to be viewed.

The first digit of the serial number will illuminate on the keypad. Press [ENTER] to see each consecutive digit. Press [CLEAR] to

exit.

6.6 Remote Control Programming

The Magellan MG5000 accepts up to thirty-two fully programmable remote controls. Programming the remote controls is

accomplished in two steps:

1) Assign the remote controls to the Magellan MG5000 control panel.

2) Program the buttons on the remote controls.

6.6.1 Assigning a Remote Control to the Magellan MG5000

Sections [611] to [642]: Remote Controls 1 to 32 respectively

Remote controls are assigned to the panel using the Automatic Learning method via the MAster Quick Menu

Programming or by entering the serial number.

6.6.2 Deleting Assigned Remote Controls

Sections [611] to [642]: Remote Controls 1 to 32 respectively

Remote controls can be deleted by deleting the corresponding user (see the Quick Menu in the MG5000 User Guide).

How Do I Assign a Remote Control to the Magellan MG5000?

1) Press the [ENTER] key.

2) Enter your [

INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)

3) Enter the desired [

SECTION NUMBER] (from sections [651] to [682]).

Enter the six-digit serial number of the remote

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Magellan MG5000 Manuel d'installation Page 25

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Magellan MG5000