Magellan MG5000 Manuel d'installation télécharger pdf (Page 23)

MG5000 19

5.4.5 Intellizone

Sections [001] to [032]: Zones 1 to 32

Option [6] OFF = Intellizone Disabled (default)

Option [6] ON = Intellizone Enabled for Selected Zone

This feature reduces the possibility of false alarms. When a zone with the Intellizone option opens, the panel does not

immediately generate an alarm. First it triggers the Intellizone Delay Timer. To program the Intellizone Delay Timer, key

in the desired 3-digit value (000 to 255 seconds, Default = 48 seconds) into section [713]. If any of the following

conditions occur during this period, the panel will generate an alarm:

• During the Intellizone Delay, a second zone has caused an alarm.

• During the Intellizone Delay, the zone in alarm has restored (closed) and re-occurred (opened).

• The zone in alarm remains open for the entire Intellizone Delay.

5.4.6 Delay Alarm Transmission

Sections [001] to [032]: Zones 1 to 32

Option [7] OFF = Delay Alarm Transmission Disabled (default)

Option [7] ON = Delay Alarm Transmission Enabled for Selected Zone

When an alarm condition occurs on a zone with this option enabled, the control panel enables the bell/siren output, but

does not report the alarm to the monitoring station until the end of the Delay Alarm Transmission. To program the

Delay Alarm Transmission, key in the desired 3-digit delay value (000 = Disabled, 001 to 255 seconds) into section

[833]. During this period, disarming the system disables the bell/siren output and cancels the report code

transmission. This feature is commonly used with entry delay zones to reduce false alarms created by new users who

may not disarm the system in time.

5.4.7 Force Zones

Sections [001] to [032]: Zones 1 to 32

Option [8] OFF = Force Zone Disabled

Option [8] ON = Selected Zone is Force Enabled (default)

Any open Force Zones at the time of arming will be considered deactivated by the control panel. If during this period a

deactivated zone is closed, the control panel will revert that zone to active status. Consequently, the control panel will

generate an alarm if the zone is breached.

Do not program a fire zone with the Force option, as the control panel will never bypass fire zones

when Force arming.

5.5 EOL Zones

Section [706]: Zone Options

Option [2] OFF = Zones do not use EOL resistors (default)

Option [2] ON = Zones require EOL resistors

If all detection devices connected to the control panel have input terminals that require 1KΩ end of line resistors, enable option

[2] in section [706]. For details on using EOL resistors, see Single Zone Inputs on page 6.

5.6 ATZ Zone Doubling

Section [705]: General Zone Options

Option [1] OFF = ATZ zone doubling disabled (default)

Option [1] ON = ATZ zone doubling enabled

Enabling ATZ Zone Doubling allows you to install two detection devices per input terminal.

5.7 ATZ Wiring Options

Section [705]: General Zone Options

Option [2] OFF = ATZ Series (default)

Option [2] ON = ATZ Parallel doubling enabled

ATZ Zone Doubling can be configured in either a series or parallel connection.

5.8 Zone Input 1 Becomes a 2-wire Smoke Input

Section [706]: General Zone Options

Option [3] OFF = Zone input 1 is a standard zone input (default)

Option [3] ON = Zone input 1 becomes a 2-wire smoke input

With this option enabled, zone input 1 becomes a 2-wire smoke input.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Magellan MG5000 Manuel d'installation Page 23

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Magellan MG5000