Magellan MG5000 Manuel d'installation télécharger pdf (Page 27)

MG5000 23

6.9 Wireless Keypad Options

Section [580]: Wireless Keypad Options

Option [1] OFF = Keypad 1 Supervision Disabled

Option [1] ON = Keypad 1 Supervision Enabled (default)

Option [2] OFF = Keypad 2 Supervision Disabled

Option [2] ON = Keypad 2 Supervision Enabled (default)

Option [3] OFF = Keypad 3 Supervision Disabled

Option [3] ON = Keypad 3 Supervision Enabled (default)

Option [4] OFF = Keypad 4 Supervision Disabled

Option [4] ON = Keypad 4 Supervision Enabled (default)

If enabled, the panel can wait for each of its assigned wireless transmitters to send a status signal within a specified time to

confirm their presence and functionality.

6.10 Wireless Keypad Live Display Mode

Section [580]: Wireless Keypad Options

Option [8] OFF = Live Display Mode Disabled

Option [8] ON = Live Display Mode Enabled (default)

The MG32LRF has two display modes. By default, the keypad will show all events (e.g. zones in alarm, bypassed zones, etc.)

live as they occur. Alternatively, with Live Display Mode off, the system will only display zones that cause an alarm or entry delay.

If you want to see the status of all zones, press the [ ] key. Zones that are open but have not triggered an alarm will only be

displayed after pressing the [ ] key. The display will appear for 30 seconds, showing the status of all zones at the time the [ ]

key was pressed. The zone display will shut off after 30 seconds.

6.11 Wireless Repeater Programming

Sections [545] to [546] represent wireless repeater 1 and 2 respectively.

The wireless repeater module will improve the range of your system by retransmitting information from zones, PGMs, wireless

keypads and the control panel. Note that all remote control signals are always repeated. You can have two MG-RPT1 per

system. The wireless repeater also provides one PGM and one zone input with two-way wireless communication with the panel.

6.12 Wireless Repeater Options

Section [551] (Repeater 1) and Section [561] (Repeater 2): Wireless Repeater Options

Option [1] OFF = Wireless Repeater Supervision (default)

Option [1] ON = Wireless Repeater Supervision

If enabled, the panel can wait for each of its wireless repeaters to send a status signal within a specified time to confirm their

presence and functionality.

Option [2] OFF = N/A

Option [2] ON = N/A

Option [3] OFF = N/A

Option [3] ON = N/A

Option [4] OFF = N/A

Option [4] ON = N/A

Option [5] OFF = Repeat Wireless Keypad 1 Signals (default)

Option [5] ON = Repeat Wireless Keypad 1 Signals enabled

Option [6] OFF = Repeat Wireless Keypad 2 Signals (default)

Option [6] ON = Repeat Wireless Keypad 2 Signals

How Do I Assign Wireless Repeaters to the MG5000?

1) Press the [ENTER] key.

2) Enter your [

INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)

3) Enter the desired [SECTION NUMBER] (from sections [545] to [546]).

4) Enter the 6-digit [SERIAL NUMBER] of the wireless repeater.

How Do I Delete Assigned Wireless Repeaters?

1) Press the [ENTER] key.

2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)

3) Enter the desired [

SECTION NUMBER] (from sections [545] to [546])

4) Press the [0] key six times to clear the serial number.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Magellan MG5000 Manuel d'installation Page 27

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Magellan MG5000