Magellan MG5000 Manuel d'installation Page 26
- Page / 56
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
22 Reference & Installation Manual
6.6.3 Programming the Remote Control Buttons
Sections [611] to [642]: Remote Controls 1 to 32 respectively
Each remote control can be programmed to perform up to 4 different actions. Each digit in sections [611] to [642]
represents a button or combination of buttons.
Warning: When section [610] is accessed, the MG5000 will copy the saved value of that section to all
remotes.
6.7 Wireless Keypad Assignment
Sections [570] to [573]
Automatic Assignment: After panel power-up, the control panel will open a 10 minute window for Automatic Assignment. Press
and hold the [] and [BYP] key for three seconds on the respective keypad. The keypad is assigned to the control panel. Up to 4
wireless keypads can be assigned within the ten minute window.
Standard Assignment: Press [
ENTER]. Enter your [INSTALLER CODE] or [MAINTENANCE CODE].
Go to section(s) [570] = Keypad 1, [571] = Keypad 2, [572] = Keypad 3, or [573] = Keypad 4.
Press and hold the [] and [
BYP] key for three seconds on the respective keypad. The keypad is assigned to the control panel.
Alternatively, enter the serial number of the MG32LRF into one of the four sections to assign it to the panel.
6.8 Viewing the Wireless Keypad Signal Strength
Sections [575] to [578]
Once wireless keypads have been installed and assigned to the Magellan MG5000, the signal strength of each transmitter can be
verified in sections [575] to [578]. Each section represents the signal strength viewer for a specific keypad. For example, section
[575] is the viewer for keypad 1 and section [578] is the viewer for the keypad 4. Sometimes moving the keypad by a small
amount will greatly increase the signal reception.
How Do I Delete a Remote Control?
1) Press the [ENTER] key.
2) Enter your [
INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)
3) Enter the desired [SECTION NUMBER] (from sections [651] to [682]).
4) Press the [0] button six times to delete the serial number.
How Do I Program the Remote Control’s Buttons?
1) Press the [ENTER] key.
2) Enter your [
INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)
3) Enter the desired [SECTION NUMBER] (from sections [610] to [642]).
4) Enter the [
HEXADECIMAL VALUE] (0 to F) of the desired button option from Table 5 on page 22 in the appropriate
space. If you do not wish to program a button combination, press the [
SLEEP] key to skip.
Table 5: Button Options
[0] = Button Disabled* [8] = Generate a Panic 1 Alarm
[1] = Regular/Regular Force arming [9] = Generate a Panic 2 Alarm
[2] = Stay/Stay Force arming [0] or [0(10)] = Generate a Panic 3 Alarm
[3] = N/A [
OFF] = Activates any PGMs that have Event Group #08 as their Activation Event
[4] = Sleep/Sleep Force arming [
BYP] = Activates any PGMs that have Event Group #09 as their Activation Event
[5] = N/A [
MEM] = Activates any PGMs that have Event Group #10 as their Activation Event
[6] = N/A [
TBL] = Activates any PGMs that have Event Group #11 as their Activation Event
[7] = N/A
[] = Paramedic alarm
* If you do not enter a value for a button, that button is disabled.
How Do I View a Wireless Keypad’s Signal Strength?
1) Press the [ENTER] key.
2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)
3) Enter the desired [SECTION NUMBER] (from sections [575] to [578]).
4) Press the keypad’s anti-tamper switch or open the corresponding keypad zone.
5) The keypad will illuminate numbers 1 to 10.
Signal Strength Indicator
8 to 10 / 3 beeps = Best signal 5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)
- MG5000 V1.4 1
- Table of Contents 3
- Part 1: Introduction 5
- Part 2: Installation 6
- MG5000 3 7
- MG5000 5 9
- 2.5 Auxiliary Power Terminals 9
- 2.6 Telephone Line Connection 9
- 2.7 Bell Output Connection 9
- 2.9 Single Zone Inputs 10
- MG5000 7 11
- 2.11 Fire Circuits 12
- Part 3: Programming Methods 13
- 3.2.3 Data Display Mode 14
- Part 4: Access Codes 15
- 4.5 User Code Options 16
- 4.6 Lock Master Code 17
- MG5000 13 17
- Part 5: Zone Programming 18
- MG5000 15 19
- MG5000 17 21
- 5.2 Zone Definition Status 21
- 5.3 Zone Partition Assignment 22
- 5.4 Zone Options 22
- MG5000 19 23
- 5.5 EOL Zones 23
- 5.6 ATZ Zone Doubling 23
- 5.7 ATZ Wiring Options 23
- Part 6: Wireless Features 24
- MG5000 21 25
- 6.3 Supervision Options 25
- 6.4 RF Jamming Supervision 25
- MG5000 23 27
- 6.9 Wireless Keypad Options 27
- MG5000 25 29
- 7.9 Timed Auto-Arming 32
- 7.10 No Movement Auto-Arming 32
- 7.14.1 Beep On Exit Delay 33
- 7.19 Exit Delay Termination 34
- 7.20 Fast Exit 34
- Part 8: Alarm Options 35
- MG5000 35 39
- 9.10 Personal Dialing Numbers 39
- 9.11 Reporting Formats 39
- 9.12 Dialing Method 40
- 9.25.1 TLM Fail Timer 42
- MG5000 39 43
- Part 10: Programmable Outputs 44
- MG5000 41 45
- 10.5 PGM Programming 45
- Part 11: System Settings 46
- 12.1.2 Number of Rings 48
- MG5000 45 49
- 12.6 Answer WinLoad Software 49
- 12.8 Call Back WinLoad 49
- Part 13: User Operation 50
- Magellan Series 47 51
- Magellan Series 49 53
- MG5000 51 55
- MG5000-EI03 56
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Magellan MG5000
(2 pages)
(68 pages)Philips LC1345 manuales
Manuales del propietario y guías del usuario para Accesorios de audio Philips LC1345.
Ofrecemos 1 manuales en pdf Philips LC1345 para descargar gratis por tipos de documentos: Manual de usuario
Commentaires sur ces manuels